C099NInverter device

• Improved motor efficiency with an important reduction of absorbed power and electric consumption.
• Reduction of noise pollution thanks to a balanced and efficient delivery of the flow rate.
• Improved piston speed for a faster approach to reach the specimen with the result of a considerable reduction in the overall test time.
• Improved reliability and life of the hydraulic pump thanks to decreased heating and mechanical stress.
• Better sensitivity of load, deformation and speed adjustment.
• Accepts both 50Hz and 60Hz supply.
• Applicable only on Servo-Plus machines.

C099-01Barcode Scanner

This instrument allows specimen file and identification by barcode reading. It can be connected to cyber-plus / servo-plus control panels by USB, to automatically register specimen code and add it as a description of the test for all tests done with compression and flexure machines. Supplied complete with USB cable.

• Codification capacity: UPC/EAN, UPC/EAN with supplements, Code 128, UCC/EAN 128, Code 39, Code 39 Full ASCII, Code 128 Full ASCII, Codabar, Interleaved 2 of 5, Code 93, MSI, Code 11, ISBN, ISSN, usw, etc…;
• Reader type: bidirectional;
• Light: 650 nm wavelength, laser-diode;
• Resolution: 0.10 mm;
• Reading distance: 3…400 mm;
• Reading angle: inclination angle 45°, elevation angle 60°.

Dimensions: 81x97x165 mm
Weight: 136 g

C097-01Dual low capacity range

(From 1/3 to 1/20 of the nominal range), complete with an Appropriate pressure transducer, hydraulic installation and cock, fitted on testing machines equipped with a digital display measuring unit.
This solution offers very high accuracy also for measurements of low strength, which is necessary to perform compression tests on mortar specimens, flexural tests on concrete beams, split cylinder tests on cylinder and cube specimens, tests on kerbs, slabs etc., by utilizing a concrete compression machine.
Recommended range: 0-250 kN

C100Splitting tensile test device for cylinders

Splitting tensile test device for cylindrical specimens

Available models:

• C100: cylinders diameter 150×300 mm, 160×320 mm, 6″x12″; height 280 mm; 20 Kg
• C101:  cylinders diameter 100×200 mm, 110×220 mm, 4″x8″; height 220 mm; 12 Kg
• C102:  cylinders diameter 40×80 mm; height 90 mm; 1 Kg

C103Splitting tensile device for cubes

Used to perform tests on concrete cube specimens 100 and 150 mm and on concrete block pavers. The maximum length of the samples is 330 mm, maximum width is 160 mm.
C103 includes a distance piece to allow testing of samples with a minimum height of 60 mm.

Dimensions: 350x250x264 mm
Weight: 17 kg approx.

C121-52Electric switch for the piston

This electric switch is fixed on the compression frame to cut off mains and to stop the machine when the maximum stroke of the piston is achieved. It can be installed only on digital compression machines.

C111-22Distance pieces for 1300, 1500, 2000, 3000 kN ASTM

Used to reduce the vertical clearance between the compression platens, according to the height of the specimen to be tested, to prevent piston overtravel. The distance pieces are placed between the ram and the lower compression plate.

Steel distance pieces are placed under the compression machine’s lower platen, to reduce the vertical daylight.
The number in brackets indicates the height of each distance piece included in the code (note that a code may contain more than one item).

C112-10Upper and lower compression platens with seat ball

Upper and lower compression platens, complete with ball seating, for tests on blocks. Two different sizes available:

• C112-10: 510x245x55 mm
• C112-11: 510x320x55 mm

E170Compression device for mortar prisms, EN standard

The compression platens have a hardness of 60 HRC and the upper platen is seat ball assembled. The centering plug is 10 mm from the compression platen, as requested by the EN 196-1 Specification.
Cadmium plated for rust protection.

Weight: 12 kg approx

SSW-LINKFirmware Upgrade for SmartLab Software

One software for multiple tests SmartLab has been developed with a modular and flexible approach to allow each laboratory to configure the software to its specific needs.
By using a Matest digital controller and a suitable firmware upgrade (SSW-LINK), any testing machines – including those from other brands – can be connected to the SmartLab platform and begin running a test. To use the SmartLab software, it is necessary to purchase the firmware license which unlocks up to 3 machines.

SmartLab can execute the following tests:

• Automatic and Manual Oedometric test;
• Automatic and Manual Shear test;
• Triaxial test;
• Compression test on concrete;
• Flexural test on concrete;
• Indirect tensile on concrete;
• Compression test on cement and mortar;
• Flexural test on cement and mortar.